+27 73 502 9614 [email protected] Mon-Sat 8:00-17:30
Slide Switches Selection Guide From Form Factor To

Slide Switches Selection Guide From Form Factor To

Browse technical resources about solar mounting systems, tracker technology, structural design, and installation best practices.

  • Selection Guide for Co-packaged Photonics Silicon Photonics for Railway Communication Grade

    Selection Guide for Co-packaged Photonics Silicon Photonics for Railway Communication Grade

    Silicon photonics has developed into a mainstream technology driven by advances in optical communications. The current generation has led to a proliferation of integrated photonic devices from t.


  • Fiber Optic Fusion Splicer Selection Guide

    Fiber Optic Fusion Splicer Selection Guide

    A fusion splicer is the most expensive tool in a fiber technician's kit. Choosing the right one means understanding splice loss specs, alignment methods, battery capacity, and field serviceability -- and knowing which features actually matter for the type of work you do. This will typically be 250µm for bare fibers and 900µm for coated fibers. These are widely used in repairs, maintenance, or installations with low fiber counts. Ribbon Fiber Splicers, however, take efficiency to another level by fusing multiple fibers (up to 12). What Is a Fiber Optic Fusion Splicer? A fusion splicer is a device that permanently joins two optical fibers by melting them together using an electric arc. Cladding. In Japan, we hold Fiber optic training where participants can systematically acquire knowledge and skills necessary for using fusion splicer, tools, and performing splicing work.

    [PDF Version]
  • Selection Guide for DFB Distributed Feedback Laser QSFP28 for Distribution Network Automation

    Selection Guide for DFB Distributed Feedback Laser QSFP28 for Distribution Network Automation

    This guide provides a systematic selection process to help you choose the right QSFP28 module every time. You will learn how to verify form factor compatibility, match fiber and distance requirements, validate switch compatibility, consider thermal constraints, and avoid. The acronym DFB laser stands for distributed feedback laser. Their key features relative to other semiconductor lasers are their single longitudinal mode (single frequency) emission profile, their high stability and their wavelength tunability. A DFB laser's periodic structure acts as a distributed reflector, providing optical feedback and. A distributed feedback (DFB) laser is a laser where the optical resonator is formed not by discrete mirrors at the ends (as in Fabry–Pérot laser diodes) but by a periodic variation of the refractive index or gain (a Bragg grating) distributed throughout the active medium.

    [PDF Version]
  • Ring Network of Aggregator Switches

    Ring Network of Aggregator Switches

    Ring aggregation networks are often employed by network carriers because of their efficiency and high fault tolerance. A fairness scheme is required in ring aggregation to achieve per-flow throughput fairness and bufferbloat avoidance, because frames are forwarded along multiple. In Figure 18-27, CEs access an RRPP ring through UPEs, and then access the backbone network through the PE-AGG. Four UPEs and one PE-AGG construct a ring in two domains: ring 1 in domain 1 and ring 1 in domain 2.


  • How to configure two core switches one primary and one backup

    How to configure two core switches one primary and one backup

    To enable Core redundancy in your design, set the Is Redundant property in Core Properties to 'Yes', and then specify the Backup Core name. Both the primary and backup Cores must be present and online during system installation so that both get configured with the. Primary and Secondary:- This means tht when you have 2 core switches connected between each other you can configure one to be primary and other to be in secondary. e when one goes down the other can take over the active role. ) If both are 6500 there is new concept of VSS which means you can. A second or Backup Core can be paired with the Primary Core in an installation. To establish a VSX relationship between the core switches, create a link aggregation (LAG) interface for assignment as the VSX data. Approved stacking for av is a two-switch stack for redundant core When the switches are stacked all multicast traffic is flooded through the stack. I have 2 core/distribution switches.

    [PDF Version]

Need Product Pricing?

Contact us for competitive quotes on any of our fiber optic products

Get a Quote